Full Issue
| View or download the full issue |
Table of Contents
| 1. Determination of the position of the contact point of a tire model with an uneven road surface for purposes of vehicle dynamical analysis | |
| Szymon Tengler, Andrzej Harlecki | 3-15 |
| 2. Mechanical analysis of autofrettaged high pressure apparatus | |
| Ruilin Zhu, Guolin Zhu, Aifeng Mao | 17-27 |
| 3. The application of self-oscillation in wire gauges | |
| Grzegorz Cieplok, Łukasz Kopij | 29-39 |
| 4. Bending and buckling of a metal seven-layer beam with lengthwise corrugated main core – comparative analysis with sandwich beam | |
| Ewa Magdalena Magnucka-Blandzi, Marcin Rodak | 41-53 |
| 5. Crack analysis in bimaterial interfaces using T-spline based XIGA | |
| Sadam Houcine Habib, Idir Belaidi | 55-68 |
| 6. The constituent equations of piezoelectric cantilevered three-layer actuators with various external loads and geometry | |
| Grzegorz Mieczkowski | 69-86 |
| 7. Quasi-Green’s function approach to fundamental frequency analysis of elastically supported thin circular and annular plates with elastic constraints | |
| Krzysztof Kamil Żur | 87-101 |
| 8. The application of the Beck`s method combined with the FEM and Trefftz functions to determine the heat transfer coefficient in minichannel | |
| Beata Maciejewska | 103-116 |
| 9. Radiative Falkner-Skan flow of Walter-B fluid with prescribed surface heat flux | |
| Tasawar Hayat, Sumaira Qayyum, Maria Imtiaz, Ahmed Alsaedi | 117-127 |
| 10. An energy-based method in phenomenological description of mechanical properties of nonlinear materials under plane stress | |
| Tadeusz Wegner, Dariusz Kurpisz | 129-139 |
| 11. A semi-theoretical model for transformation plasticity occurred during bainitic transformation | |
| Mahmoud Yaakoubi, Fakhreddine Dammak | 141-153 |
| 12. Generalized thermoelastic functionally graded half space under surface absorption of a laser radiation | |
| Mohamed N. M. Allam, Ismail M. Tayel | 155-165 |
| 13. Modeling of thermal processes proceeding in 1D domain of crystalline solids using the lattice Boltzmann method with interval source function | |
| Alicja Piasecka-Belkhayat, Anna Korczak | 167-175 |
| 14. Large deformation analysis and stability analysis of a cylindrical rubber tube under internal pressure | |
| Jianbing Sang, Sufang Xing, Haitao Liu, Xiaolei Li, Jingyuan Wang, Yinlai Lv | 177-188 |
| 15. An investigation of stresses and deformation states of clamped rotating functionally graded disk | |
| Amit Kumar Thawait, Lakshman Sondhi, Shubhashis Sanyal, Shubhankar Bhowmick | 189-198 |
| 16. Analysis of strain localization in porous media with transversely isotropic elasticity under undrained conditions | |
| Y.Q. Zhang, L.Z. Wang, Miao Pang, L.F. Fan | 199-211 |
| 17. Modeling and analysis for coupled flexural-torsional spinning beams with unsymmetrical cross sections | |
| Jie Wang, Dongxu Li, Jianping Jiang | 213-226 |
| 18. Synchronization and stability of an elastically coupled tri-rotor vibration system | |
| Yongjun Hou, Mingjun Du, Pan Fang, Liping Zhang | 227-240 |
| 19. Experimental validation of the use of energy transfer ratio (ETR) for damage diagnosis of steel-concrete composite beams | |
| Tomasz Wróblewski, Małgorzata Jarosińska, Małgorzata Abramowicz, Stefan Berczyński | 241-252 |
| 20. Modal analysis of gearbox transmission system in Bucket wheel excavator | |
| Maha Karray, Nabih Feki, Mohamed Taoufik Khabou, Fakher Chaari, Mohamed Haddar | 253-264 |
| 21. Design and implementation of improved sliding mode controller on 6R manipulator | |
| Moharam H. Korayem, Saeed Rafee Nekoo, Alireza Khademi, Faezeh Abdollahi | 265-280 |
| 22. Dynamic response of ladder track rested on stochastic foundation under oscillating moving load | |
| Saeed Mohammadzadeh, Mohammad Mehrali | 281-291 |
| 23. Numerical loss analysis on slot-type casing treatment in a transonic compressor stage | |
| Ming-Min Zhu, Xiao-Qing Qiang, Jin-Fang Teng | 293-306 |
| 24. Preliminary design of an adaptive aileron for next generation regional aircraft | |
| Gianluca Amendola, Ignazio Dimino, Antonio Concilio, Francesco Amoroso, Rosario Pecora | 307-316 |
| 25. Numerical study of droplet formation in a Y-junction microchannel | |
| Mouhamadou Moustapha Lamine Diouf, Oldrich Joel Romero | 317-330 |
| 26. Numerical creep analysis of FGM rotating disc with GDQ method | |
| Hodais Zharfi, Hamid Ekhteraei Toussi | 331-341 |
| 27. A novel approach to thermal and mechanical stresses in a FGM cylinder with exponentially-varying properties | PDF PDF |
| Kerimcan Celebi, Durmuş Yarimpabuç, Ibrahim Keles | 343-351 |
| 28. High order sensitivity analysis of a mistuned blisk including intentional mistuning | |
| Linus Pohle, Sebastian Tatzko, Lars Panning-von Scheidt, Jörg Wallaschek | 353-368 |
| 29. Anatomical protocol for gait analysis: joint kinematics measurement and its repeatability | |
| Magdalena Żuk, Marta Trzeciak | 369-376 |
| 30. Automotive vehicle engine mount based on an MR squeeze-mode damper: modeling and simulation | |
| Bogdan Sapiński, Jacek Jan Snamina | 377-388 |